AVR C 语言编程基础

# AVR C 语言编程基础

In this chapter you will explore some of the key concepts of C programming for AVR microcontrollers.

1. 3.1   AVR Registers
2. 3.2   Bits and Bytes
3. 3.3   Bitwise Operations
4. 3.4   Clearing and Setting Bits
5. 3.5   The Bit Value Macro _BV()

### 3.1  AVR寄存器

A register is a special storage space in which the state of the bits in the register have some special meaning to the AVR microcontroller. Most of the registers are 8-bits wide (there are a few exceptions). Each register has a name and individual bits may also have unique names. All of the register and bit names are described in the ATmega48/88/168/328 datasheet. The AVR Libc library will define identifiers for the register names and bit names so that they can be easily accessed in C. Manipulating the bits in the various registers of the AVR is the basis for AVR programming. Everything from configuring the AVR device's built-in peripherals to using the AVR's pins for digital I/O is done by manipulating bits in these registers.

### 3.2  位和字节

A bit represents one of two possible states: 1 or 0 (aka: on/off, set/clear, high/low). Several bits together represent numerical values in binary, where each bit is one binary digit. An AVR microcontroller groups 8 bits together to form one byte wtih the Least Significant Bit (LSB) on the right. Each bit is numbered, starting from 0, at the LSB. Consider the decimal number 15 for example. 15 represented in 8-bit binary is 00001111. The 4 least significant bits 0, 1, 2, and 3, are set.

Figure 3.1 - The decimal number 15 represented in 8 bits If you do not already know how to convert numbers between decimal, binary, and hexadecimal, you can find numerous lessons online or use my Printable Decimal-Binary-Hex Conversion Chart Another example, the decimal number 40 is represented in binary as 00101000. Bits 3 and 5 are set.

Figure 3.2 - The decimal number 40 represented in 8 bits Numerical values in a C program for an AVR microcontroller may be defined using a decimal, hexadecimal, or binary notation depending on the context and the programmer's preference. A hexadecmial number is defined using the 0x prefix and a binary number is defined using the 0bprefix. The following C code shows 3 ways in which a variable might be initialized to the decimal value of 15. uint8_t a = 15;         /* decimal */ uint8_t b = 0x0F;       /* hexidecimal */ uint8_t c = 0b00001111; /* binary */ The uint8_t data type is one of the fixed width integer types from the C99 standard. It defines an 8-bit unsigned integer. The C99 style data types will be used throughout this tutorial series.

### 3.3  位运算

Since individual bits often have a significant meaning when programming AVR microcontrollers, bitwise operations are very important. A bitwise AND operation results in bits being set only if the same bits are set in both of the operands. In other words: bit n will be set in the result if bit n is set in the first operand and the second operand.

Figure 3.3 - Bitwise AND operation A single ampersand character (&) is the bitwise AND operator in C. uint8_t a = 0xAA; /* 10101010 */ uint8_t b = 0x0F; /* 00001111 */ uint8_t = a & b;  /* 00001010 */ A bitwise OR operation results in bits being set if the same bits are set in either of the operands. In other words: bit n will be set in the result if bit n is set in the first operand or the second operand.

Figure 3.4 - Bitwise OR operation A single pipe character (|) is the bitwise OR operator in C. uint8_t a = 0xAA; /* 10101010 */ uint8_t b = 0x0F; /* 00001111 */ uint8_t = a | b;  /* 10101111 */ A bitwise XOR operation ("exclusive or") results in bits being set if, and only if, the same bit is set in one of the operands but not the other. In other words: bit n will be set in the result if bit n is exclusively set in only one of the operands.

Figure 3.5 - Bitwise XOR operation The caret character (^) is the bitwise XOR operator in C. uint8_t a = 0xAA; /* 10101010 */ uint8_t b = 0x0F; /* 00001111 */ uint8_t = a ^ b;  /* 10100101 */ A NOT operation, also known as a one's complement, is a unary operation. That means the operation is performed on a single value instead of two. The NOT operation will simply negate each bit. Every 1 becomes 0 and every 0 becomes 1.

Figure 3.6 - Bitwise NOT operation A tilde character (~) is the NOT operator in C. uint8_t a = 0xAA; /* 10101010 */ uint8_t b = ~a;   /* 01010101 */ A shift operation shifts all of the bits to the left or the right. In a left shift, bits get "shifted out" on the left and 0 bits get "shifted in" on the right. The opposite goes for a right shift.

Figure 3.7 - Bitwise shift operation Two less-than symbols (<<) is the left shift operator and two greater-than symbols (>>) is the right shift operator in C. The right side of the operator is the number of bits to shift. uint8_t a = 0x99; /* 10011001 */ uint8_t b = a<<1; /* 00110010 */ uint8_t c = a>>3; /* 00010011 */

### 3.4  Clearing and Setting Bits

Setting and clearing a single bit, without changing any other bits, is a common task in AVR microcontroller programming. You will use these techniques over and over again. When manipulating a single bit, it is often necessary to have a byte value in which only the bit of interest is set. This byte can then be used with bitwise operations to manipulate that one bit. Let's call this a bit value mask. For example, the bit value mask for bit 2 would be 00000100 and the bit value mask for bit 6 would be 01000000. Since the number 1 is represented in binary with only bit 0 set, you can get the bit value mask for a given bit by left shifting 1 by the bit number of interest. For example, to get the bit value mask for bit 2, left shift 1 by 2.

Figure 3.7 - Bit value mask To set a bit in C, OR the value with the bit value mask. uint8_t a = 0x08; /* 00001000 */                  /* set bit 2 */ a |= (1<<2);      /* 00001100 */ Use multiple OR operators to set multiple bits. uint8_t a = 0x08;   /* 00001000 */                    /* set bits 1 and 2 */ a |= (1<<2)|(1<<1); /* 00001110 */ To clear a bit in C, NOT the bit value mask so that the bit of interest is the only bit cleared, and then AND that with the value. uint8_t a = 0x0F; /* 00001111 */                  /* clear bit 2 */ a &= ~(1<<2);     /* 00001011 */ Use multiple OR operators to clear multiple bits. uint8_t a = 0x0F;      /* 00001111 */                       /* clear bit 1 and 2 */ a &= ~((1<<2)|(1<<1)); /* 00001001 */ To toggle a bit in C, XOR the value with the bit value mask. uint8_t a = 0x0F; /* 00001111 */                  /* toggle bit 2 */ a ^= (1<<2);      /* 00001011 */ a ^= (1<<2);      /* 00001111 */

### 3.5  The Bit Value Macro _BV()

AVR Libc defines a the _BV() macro which stands for "bit value". It is a convenience macro to get the bit value mask for a given bit number. The idea is to make the code a little more readable over using a bitwise left shift. Using _BV(n) is functionally equivelent to using (1</* set bit 0 using _BV() */ a |= _BV(0); /* set bit 0 using shift */ a |= (1<<0); Which method you choose is entirely up to you. You will see both in wide use and should be comfortable seeing either. Since the _BV(n) macro is unique to gcc, it is not as portable to other compilers as the (1<

• 